ELGA PURELAB 7120 - ProfiLab24 GmbH
99
100
24
4
stars -
Professional service
Customer
Young team with a lot of ambition and quick answers to all questions. We needed a complete laboratory equipment for our new location. The team of Profiab24 has arranged everything.
ELGA PURELAB 7120 in Water Stills, Water Treatment
ELGA PURELAB 7120 at ProfiLab24 dealer for laboratory equipment. Made in Germany with top advice and 24H service.
ELGA PURELAB 7120The PURELAB 7000 series is designed for applications requiring higher flows of Type II pure water or as a pure water feed system for small distribution loops. The system can supply water from the internal 50 liter reservoir at varying flow rates or can feed into much larger vessels as required.
- Small high purity distribution system with variable flow rates
- Auto rinse and simple sanitization procedures maintain the purity of water for the life of the system
For operating a PURELAB 3000/7000 system, a starter kit 1 or 2 is required.
|
Booster pump:
|
without
|
|
Power:
|
120 l/h
|
|
Storage tank - tank:
|
with
|
|
Water treatment type:
|
pure water system
|
|
Water source:
|
of ion exchangerfrom the water mains
|
| Product weight: |
60,00 Kg |
| Model |
PURELAB 7120 |
| Treated Water Specifications |
|
| Make-up rate at 15°C |
120 l/hr |
| Daily usage - typical |
960 liters |
| Daily usage - maximum |
2880 liters |
| Delivery flowrate |
Up to 4 l/min at 12 psi (0.8 bar) 1)
|
| Inorganics rejection |
- |
| Inorganics (resistivity at 25°C) |
>15 MOhm-cm |
| Bacteria - typical |
<1 CFU/ml |
| Organics (TOC) - typical |
<10 ppb |
| Particles |
0.05 µm |
| Dimensions and weights |
|
| Dimensions |
Height 820mm (32.8in)
834mm (33.4in) including castors
Width 794mm (31.8in)
Depth 470mm (18.8in) |
| Supply weight |
53kg |
| Operational weight |
110kg |
| Installation |
Floor/bench |
| Feedwater Requirements |
|
| Source |
Tap water as detailed below |
| Contaminant |
|
| Conductivity |
<2000 µS/cm*
|
| Hardness |
<250 ppm as CaCO3
|
| Free chlorine |
<4 ppm Cl2
|
| Chloramine |
<1 ppm as Cl2
|
| Silica |
<30 ppm SiO2
|
| Fouling Index |
<10 FI |
| Iron/manganese |
<0.1 ppm Fe/Mn |
| Organics |
<3 ppm TOC |
| Temperature |
4 - 40°C
(Recommended 15 - 25°C) |
| Flowrate (maximum requirement at 15°C) |
9 l/min |
| Drain requirements (gravity fall with air gap) |
20 l/min |
| Feedwater pressure |
6 bar (90 psi) maximum
2 bar (30 psi) minimum |
| Electrical Requirements |
|
| Mains input |
230V ac, 50Hz
115V ac, 60Hz |
| System control voltage (not including pumps and UV) |
24V dc |
| Power consumption (peak demand) |
650VA |
| Electrical protection rating |
10 amps |
Specifications are for a system fed with a suitable water supply and installed, operated and sanitized according to the operator manuals.
1) With High Flow Kit (LA723) or 2 l/min at 12 psi (0.8 bar) without high flow kit
Failure to comply with the feedwater pretreatment recommendations will affect the life and performance of key components and may invalidate the warranty. Feedwater requirements are specified for units fitted with a Protek L2 pretreatment cartridge. If feedwater purity is variable or values are outside any of the above ranges, additional pretreatment is recommended to be installed in the feedwater supply to the unit.
* Deionization cartridge life may vary with feedwater >1400 µS/cm
