BINDER FDL 115 Safety drying oven
The BINDER FDL 115 with silicone and dust-free inner chamber, as well as symmetric airflow dries specimens containing solvents and thus this safety drying oven meets all EN 1539 requirements.
Advantages
- Defined solvent quantity according to EN 1539
- Wide temperature range up to 300 °C
- Overtemperature monitoring
- Exhaust airflow monitoring
Areas of application
- Chemicals
- Surface Technology
Performance characteristics
- Electronically controlled APT.lineTM preheating chamber assuring temperature accuracy and reproducible results All safety features met according to EN 1539
- Temperature range from 10 °C above ambient temperature to 300 °C
- Controller with 2 programs with 10 sections each, or alternatively one program with 20 sections
- The time of an individual program step can be set to max. 99.59 hours or 999.59 hours. This adjustment applies to all program sections.
- Integrated weekly program timer with real-time function
- Adjustable ramp function via program editor
- Digital temperature setting with an accuracy of one degree
- Elapsed time indicator
- Door gasket FKM (for max. temperature of 200 °C / 392 °F)
- Replaceable fresh-air filter cartridge. Class F6 (EU6 fine-particle filter for particle sizes 1 µm to 10 µm)
- Independent adjustable temperature safety device class 2 (DIN 12880), with visual temperature alarm
- Fresh-air monitoring with visual and audible alarm and automatic deactivation of heating
- Rear exhaust connector Ø 100 mm (4 inch)
- RS 422 interface for use with APT-COMTM DataControlSystem communication software
- Units up to 115 liters are stackable
- 2 chrome-plated racks included
- BINDER test confirmation
|
Load max.:
|
51 - 100 kg
|
|
Width outside (incubators,...):
|
830 mm
|
|
Width inside (incubators,...):
|
600 mm
|
|
Maximum temperature (heat):
|
+ 300 °C
|
|
Height outside (incubators,...):
|
805 mm
|
|
Height inside (incubators,...):
|
435 mm
|
|
Interior volume:
|
101 - 200 l
|
|
Cabinet type:
|
safety drying ovenheating oven
|
|
Depth outside (incubators,...):
|
685 mm
|
|
Depth inside (incubators,...):
|
435 mm
|
| Shipping weight: |
102,00 Kg |
| Product weight: |
90,00 Kg |
| Dimensions: |
× × cm |
| BINDER Safety drying oven |
FDL 115 |
|
|
| Exterior dimensions |
|
| Housing |
|
| Width (mm) |
830 |
| Height (incl. feet/castors) (mm) |
805 |
| Depth (plus connections and fittings) (mm) |
685 |
| Depth (incl. connections and fittings) (mm) |
745 |
| Wall clearance, rear (mm) |
100 |
| Wall clearance, side (mm) |
100 |
| Exhaust duct (outer Ø mm) |
100 |
| Steam space volume (l) |
156 |
| Interior dimensions |
|
| Width (mm) |
600 |
| Height (mm) |
435 |
| Depth (mm) |
435 |
| Interior volume (l) |
115 |
| Racks (number standard/max.) |
2/5 |
| Load per rack (kg) |
30 |
| Permitted total load (kg) |
60 |
| Weight (empty) (kg) |
90 |
| Temperature data |
|
| Temperature range approx. 10 °C above ambient temperature to (°C) |
300 |
| Temperature variation |
|
| at 50 °C (± K) |
0,5 |
| at 150 °C (± K) |
2,5 |
| at 300 °C (± K) |
5,8 |
| Temperature fluctuation (± K) |
0,8 |
| Warm-up time 1)
|
|
| to 50 °C (min.) |
10 |
| to 150 °C (min.) |
18 |
| to 300 °C (min.) |
63 |
| Recovery time after doors were open for 30 sec. |
|
| at 50 °C (min.) |
12 |
| at 150 °C (min.) |
7 |
| at 300 °C (min.) |
14 |
| Ventilation data |
|
| Ventilation (approx. x/min.) |
2,5 |
| Air circulation (approx. x/min.) |
20 |
| Exhaust air volume flow (approx. l/min.) |
400 |
| Exhaust air volume flow (approx. m³/h.) |
24 |
| Highest permitted solvent quantity (at T-180 °C, M-100g/mol, U-40g/m3, K=0.5) (g) 1) |
6,65 |
| Electrical data |
|
| IP protection class acc. to EN 60529 |
IP 33 |
| Voltage (± 5%) |
50/60 Hz (V) 230 |
| Nominal power (kW) |
2,9 |
| Energy consumption |
|
| at 150 °C (Wh/h) |
1200 |
| Noise level |
57 dB(A) |
1)
- T = drying temperature
- M = molecular mass
- U = lower explosion limit
- K = solvent vapor concentration as percentage of lower explosion limit
All technical data are specified for units with standard equipment at an ambient temperature of 25 °C and a line voltage fluctuation of ±5%. The temperature data is determined in accordance to factory standard following DIN 12880, respecting the recommended wall clearances of 10% of the height, width and depth of the inner chamber. All figures are typical average values for series devices. We reserve the right to alter technical specifications at any time.
| Customer benefits |
|
|
|
|
|
| Features |
Customer benefits |
Characteristics |
| APT.lineTM
|
Same test conditions throughout the chamber interior
Independent of specimen size and quantity |
APT.lineTM preheating chamber technology for maximum precision
Uniform circulation throughout the inner chamber
Homogeneous temperature conditions throughout test specimens |
| Safety concept |
Defined solvent quantity
Safe standard-compliant drying |
Complies with EN 1539:
Fresh air monitoring with automatic switchoff
Audible and visual alarm
Class 2 independent adjustable temperature safety device
Safety class IP 33
Easy to replace fresh air filter |
| Performance feature |
Short warm up times
Broad range of applications, e.g. coil coating tests |
High air exchange rate
Monitored air exchange volume
Large power reserves
Temperature range up to 300 °C |
| Inner chamber concept |
Maximum occupational safety
Easy loading and unloading of specimen material
Easy to clean |
Low heat dissipation due to 60 mm insulation
Rack with tilt protection
Complete inner chamber made of stainless steel
No permanent fixtures
Silicone free
Viton (FKM) door seal |
| Controller |
Programmable controller with intelligent temperature control and weekly program timer |
Convenient operation and documentation |
| Unit options and service |
Optimal solution for numerous applications
BINDER INDIVIDUAL for customer-specific solutions
Worldwide BINDER Service |
Various options: temperature measurement of the specimen, calibration certificate
Control and documentation software APT-COMTM
Drying ovens, vacuum drying ovens, climate chambers
Worldwide service network |
